Ziveli
Membre Junior
salut a tous, j'aurais besoin de vos lumières :god-17c6:
je n'arrive pas a stabiliser mon OC de mon Quad Q9450 a 3.7Ghz avec ma Rampage extreme, chose que je suis arrivé les doigts dans le nez avec ma Maximus II Formula (peut être pas a ce point mais presque) mais que cette têtu de Rampage m'en empêche (chipset X48 surement ???) :enerv::enerv::enerv:
il est actuellement a 3.2Ghz car des que je commence a grimper en FSB au dessus de 400, (sans toucher a la RAM que je laisse synchronisé a 1:1), et j'en ai essayer des réglage, aucun test OCCT, CPU Stress ou autre ne tiens (erreur coeur 0/1/2 ou 3)
voila mes reglage de bios actuel avec FSB de 400mhz
Ai Overclock Tuner Manual
OC From CPU Level Up Auto
OC From Memory Level Up Auto
FSB Frequency 400
CPU Ratio Setting 8
> Configuration du CPU
*CPU Clock Skew Auto
*NB Clock Skew Auto
FSB Strap to North Bridge 333MHz
PCIE Frequency 100
DRAM Frequency Auto
DRAM Command Rate Auto
DRAM Timing Control Auto
CAS# Latency
RAS# to CAS#
RAS# PRE Time
RAS# ACT Time
RAS# to RAS# Delay Auto
REF Cycle Time Auto
WRITE Recovery Time Auto
READ to PRE Time Auto
2nd Information : 10-5-5-4-7-4-7
READ to WRITE Delay (S/D) Auto
WRITE to READ Delay (S) Auto
WRITE to READ Delay (D) Auto
READ to READ Delay (S) Auto
READ to READ Delay (D) Auto
WRITE to WRITE Delay (S) Auto
WRITE to WRITE Delay (D) Auto
3rd Information :
WRITE to PRE Delay Auto
READ to PRE Delay Auto
PRE to PRE Delay Auto
ALL PRE to ACT Delay Auto
ALL PRE to REF Delay Auto
DRAM Stactic Read Control Auto
DRAM Dynamic Write Control Auto
> DRAM Skew Control
Ai Clock Twister Auto
Ai Transaction Booster Auto
C/P : A1 A2 A3 A4 A5 I B1 B2 B3 B4 B5
LVL : 10 10 10 10 10 I 10 10 10 10 10
----------------------------------------------------
EPU II Phase Control Auto
*** Please Key in numbers or select voltage!***
Voltage du CPU 1.287
Load-Line Calibration Activé
CPU PLL Voltage 1.617
FSB Termination Voltage 1.418
CPU GTLVref (0) Auto
CPU GTLVref (1) Auto
CPU GTLVref (2) Auto
CPU GTLVref (3) Auto
NB GTLVref Auto
North Bridge Voltage 1.550
DRAM Volatge 1.65681
NB DDRVref Auto
DDR3 ChannelA Vref Auto
DRR3 ChannelB Vref Auto
South Bridge 1.5 Voltage 1.51106
South Bridge 1.05 Voltage 1.060
****************************************
CPU Spread Spectrum Désactivé
PCIE Spread Spectrum Désactivé
et ceux que j'utilise pour monté a nouveau a 3.7Ghz
Ai Overclock Tuner Manual
OC From CPU Level Up Auto
OC From Memory Level Up Auto
FSB Frequency 463
CPU Ratio Setting 8
> Configuration du CPU
*CPU Clock Skew Auto
*NB Clock Skew Auto
FSB Strap to North Bridge 333MHz
PCIE Frequency 100
DRAM Frequency Auto
DRAM Command Rate 2N
DRAM Timing Control Auto
1st Information :
CAS# Latency
RAS# to CAS# Delay
RAS# PRE Time
RAS# ACT Time
RAS# to RAS# Delay Auto
REF Cycle Time Auto
WRITE Recovery Time Auto
READ to PRE Time Auto
2nd Information : 10-5-5-4-7-4-7
READ to WRITE Delay (S/D) Auto
WRITE to READ Delay (S) Auto
WRITE to READ Delay (D) Auto
READ to READ Delay (S) Auto
READ to READ Delay (D) Auto
WRITE to WRITE Delay (S) Auto
WRITE to WRITE Delay (D) Auto
3rd Information : 21-7-1-10-10
WRITE to PRE Delay Auto
READ to PRE Delay Auto
PRE to PRE Delay Auto
ALL PRE to ACT Delay Auto
ALL PRE to REF Delay Auto
DRAM Stactic Read Control Auto
DRAM Dynamic Write Control Auto
DRAM Skew Control
Ai Clock Twister Moderate
Ai Transaction Booster Auto
C/P : A1 A2 A3 A4 A5 I B1 B2 B3 B4 B5
LVL : 10 10 10 10 10 I 10 10 10 10 10
----------------------------------------------------
EPU II Phase Control Auto
*** Please Key in numbers or select voltage!***
Voltage du CPU 1.34...
Load-Line Calibration Activé
CPU PLL Voltage 1.68..
FSB Termination Voltage 1.524
CPU GTLVref (0) Auto
CPU GTLVref (1) Auto
CPU GTLVref (2) Auto
CPU GTLVref (3) Auto
NB GTLVref Auto
North Bridge Voltage 1.55..
DRAM Volatge 1.65681
NB DDRVref Auto
DDR3 ChannelA Vref Auto
DRR3 ChannelB Vref Auto
South Bridge 1.5 Voltage 1.51106
South Bridge 1.05 Voltage 1.12664
****************************************
CPU Spread Spectrum Désactivé
PCIE Spread Spectrum Désactivé
Merci d'avance :hat-1194:
je n'arrive pas a stabiliser mon OC de mon Quad Q9450 a 3.7Ghz avec ma Rampage extreme, chose que je suis arrivé les doigts dans le nez avec ma Maximus II Formula (peut être pas a ce point mais presque) mais que cette têtu de Rampage m'en empêche (chipset X48 surement ???) :enerv::enerv::enerv:
il est actuellement a 3.2Ghz car des que je commence a grimper en FSB au dessus de 400, (sans toucher a la RAM que je laisse synchronisé a 1:1), et j'en ai essayer des réglage, aucun test OCCT, CPU Stress ou autre ne tiens (erreur coeur 0/1/2 ou 3)
voila mes reglage de bios actuel avec FSB de 400mhz
Ai Overclock Tuner Manual
OC From CPU Level Up Auto
OC From Memory Level Up Auto
FSB Frequency 400
CPU Ratio Setting 8
> Configuration du CPU
*CPU Clock Skew Auto
*NB Clock Skew Auto
FSB Strap to North Bridge 333MHz
PCIE Frequency 100
DRAM Frequency Auto
DRAM Command Rate Auto
DRAM Timing Control Auto
CAS# Latency
RAS# to CAS#
RAS# PRE Time
RAS# ACT Time
RAS# to RAS# Delay Auto
REF Cycle Time Auto
WRITE Recovery Time Auto
READ to PRE Time Auto
2nd Information : 10-5-5-4-7-4-7
READ to WRITE Delay (S/D) Auto
WRITE to READ Delay (S) Auto
WRITE to READ Delay (D) Auto
READ to READ Delay (S) Auto
READ to READ Delay (D) Auto
WRITE to WRITE Delay (S) Auto
WRITE to WRITE Delay (D) Auto
3rd Information :
WRITE to PRE Delay Auto
READ to PRE Delay Auto
PRE to PRE Delay Auto
ALL PRE to ACT Delay Auto
ALL PRE to REF Delay Auto
DRAM Stactic Read Control Auto
DRAM Dynamic Write Control Auto
> DRAM Skew Control
Ai Clock Twister Auto
Ai Transaction Booster Auto
C/P : A1 A2 A3 A4 A5 I B1 B2 B3 B4 B5
LVL : 10 10 10 10 10 I 10 10 10 10 10
----------------------------------------------------
EPU II Phase Control Auto
*** Please Key in numbers or select voltage!***
Voltage du CPU 1.287
Load-Line Calibration Activé
CPU PLL Voltage 1.617
FSB Termination Voltage 1.418
CPU GTLVref (0) Auto
CPU GTLVref (1) Auto
CPU GTLVref (2) Auto
CPU GTLVref (3) Auto
NB GTLVref Auto
North Bridge Voltage 1.550
DRAM Volatge 1.65681
NB DDRVref Auto
DDR3 ChannelA Vref Auto
DRR3 ChannelB Vref Auto
South Bridge 1.5 Voltage 1.51106
South Bridge 1.05 Voltage 1.060
****************************************
CPU Spread Spectrum Désactivé
PCIE Spread Spectrum Désactivé
et ceux que j'utilise pour monté a nouveau a 3.7Ghz
Ai Overclock Tuner Manual
OC From CPU Level Up Auto
OC From Memory Level Up Auto
FSB Frequency 463
CPU Ratio Setting 8
> Configuration du CPU
*CPU Clock Skew Auto
*NB Clock Skew Auto
FSB Strap to North Bridge 333MHz
PCIE Frequency 100
DRAM Frequency Auto
DRAM Command Rate 2N
DRAM Timing Control Auto
1st Information :
CAS# Latency
RAS# to CAS# Delay
RAS# PRE Time
RAS# ACT Time
RAS# to RAS# Delay Auto
REF Cycle Time Auto
WRITE Recovery Time Auto
READ to PRE Time Auto
2nd Information : 10-5-5-4-7-4-7
READ to WRITE Delay (S/D) Auto
WRITE to READ Delay (S) Auto
WRITE to READ Delay (D) Auto
READ to READ Delay (S) Auto
READ to READ Delay (D) Auto
WRITE to WRITE Delay (S) Auto
WRITE to WRITE Delay (D) Auto
3rd Information : 21-7-1-10-10
WRITE to PRE Delay Auto
READ to PRE Delay Auto
PRE to PRE Delay Auto
ALL PRE to ACT Delay Auto
ALL PRE to REF Delay Auto
DRAM Stactic Read Control Auto
DRAM Dynamic Write Control Auto
DRAM Skew Control
Ai Clock Twister Moderate
Ai Transaction Booster Auto
C/P : A1 A2 A3 A4 A5 I B1 B2 B3 B4 B5
LVL : 10 10 10 10 10 I 10 10 10 10 10
----------------------------------------------------
EPU II Phase Control Auto
*** Please Key in numbers or select voltage!***
Voltage du CPU 1.34...
Load-Line Calibration Activé
CPU PLL Voltage 1.68..
FSB Termination Voltage 1.524
CPU GTLVref (0) Auto
CPU GTLVref (1) Auto
CPU GTLVref (2) Auto
CPU GTLVref (3) Auto
NB GTLVref Auto
North Bridge Voltage 1.55..
DRAM Volatge 1.65681
NB DDRVref Auto
DDR3 ChannelA Vref Auto
DRR3 ChannelB Vref Auto
South Bridge 1.5 Voltage 1.51106
South Bridge 1.05 Voltage 1.12664
****************************************
CPU Spread Spectrum Désactivé
PCIE Spread Spectrum Désactivé
Merci d'avance :hat-1194:
